AIA CONTINUING EDUCATION
Ron Hunsicker is a registered provider for the AIA system of continuing education to architects. The seven AIA-approved in-office seminars offered may also be acceptable for continuing education for engineers.
All seminars except "Detailing Masonry Veneers to Avoid Water Penetration and Cracks" are one hour long and earn one learning unit. "Detailing Masonry Veneers to Avoid Water Penetration and Cracks" requires 1-1/2 hours and earns 1-1/2 learning units.
Avoiding Water Penetration in Masonry Veneers (RJH001)
Because a single wythe of any type of masonry will not keep all of the water out, all of the time, a system has been developed which does keep all of the water out, all of the time. This system is known as a drainage wall system -- a combination of a veneer, an air space, through-wall flashings, and weepholes. "Avoiding Water Penetration"Â explains how to design a drainage wall system, including selecting a mortar joint profile and a mortar type, setting the width of the air space, sorting out flashing materials, placing weepholes properly, detailing through-wall flashings, and specifying the bricks used in the veneer.
Movement in Clay Masonry Veneers (RJH002)
Although rarely seen in single family houses, movement joints are used to prevent cracking of masonry in other structures. Learn what causes movement, how much movement to expect, how to control movement, and where to place movement joints. Sealants, an integral part of a movement joint, are also discussed. Learn why a C.J. is not a M.J.
Detailing Masonry Veneers to Avoid Water Penetration and Cracks (RJH003)
A combination of an abridged "Avoiding Water Penetration" and an abridged "Movement in Clay Masonry Veneers." (1-1/2 hours / 1-1/2 Learning Units)
Mortars for Masonry Veneers (RJH004)
Masonry veneers have four parts; design, the masonry units, the mortar, and workmanship. Mortars are usually the least understood. Learn about masonry cements and Portland cement/hydrated lime mortars. Understand the difference between a proportion specification and a property specification. Learn which mortar is used where.
Cleaning New Masonry (RJH005)
Many good buildings have been damaged by bad cleaning. "Clean it with acid" is often not the right way. Using it "straight" is almost always wrong. Learn how to clean anything. Come to understand how chemicals help clean masonry. Explore the process of cleaning masonry, starting with learning how to avoid cleaning.
Masonry Veneers with Stud Back-up (RJH006)
Masonry veneers anchored to wood stud and steel stud back-up systems are very popular in both residential and non-residential construction. While wood stud systems are almost intuitive and are very forgiving, steel stud systems require more care. Explore the basics of detailing any masonry veneer/stud back-up system. Learn about air spaces, the correct mortar type, selection of steel studs, fasteners, and ties. Consider the location of insulation and vapor retarders.
Building with Clay Brick Shapes (RJH008)
If a wall needs more impact, watertables, soldier courses, and sills are quick solutions. Lipped brick disguise the horizontal movement joints which accommodate vertical movement; sills and caps move water away from walls and to the ground. Radial bricks turn sharp corners into smooth paths. Customizing a specification assures the look a designer imagined. Building with Clay Brick Shapes explores how clay brick shapes are manufactured and when and how to use them.
ASTM Standard Specifications in Contract Documents (RJH009)
Construction specifications rely on documents developed by ASTM International® to establish needed levels of quality for almost all materials used in construction. In many cases, ASTM® documents also describe proper methods of installation and explain how to avoid problems commonly associated with some materials. Regardless this reliance, most designers have not read any of these documents. Regardless this reliance, few understand why one product meets the requirements of an ASTM standard specification and another product does not.
“ASTM Standard Specifications in Contract Documents,” explains the standards development process and how this process has been designed to protect the public from damage to property and personal injury caused by products that are incapable of performing as they must. Beyond specifications for materials, products, and systems, this seminar explains how test methods, laboratory certifications, standard practices, and guides support the product specifications goal of protecting the public interest. This seminar also introduces attendees to the most-used clay brick and concrete brick specifications and test methods. Once specifying products and methods is explained, the nuances of a clay brick specification are explored, as are evaluating and interpreting test reports.